انجمن زمین شناسی مهندسی ایراننشریه انجمن زمین شناسی مهندسی ایران2228-524514320211122Assessing and Predicting the Vibration Signals in Rock Machining Processبررسی و پیش بینی سیگنالهای ارتعاشی در فرآیند سنگ زنی2332133729FAرضا میکائیلگروه مهندسی معدن، دانشکده محیط زیست دانشگاه صنعتی ارومیهاکبر اسمعیل زادهگروه معدن، دانشکده محیط زیست، دانشگاه صنعتی ارومیه، ارومیه، ایران0000-0002-8633-9683محمد عطاییاستاد دانشکده معدن دانشگاه صنعتی شاهرود0000-0002-7016-8170Journal Article20200705Besides stone perishing, generated vibrations during stone cutting process can lead to bending, deflection and finally breakage of cutter disks. Therefore, study and predicting vibrations, is unavoidable in stone cutting process. In this research, by means of laboratory and statistically analysis, a study is carried out to predicting vibration of stone cutting process. For this purpose, a stone cutting machine in laboratory scale which equipped with vibration measurement tools, was provided. On a carbonate rock specimen, the study is carried out under different circumstance such as different practical cut depth (15, 22, 30, 35 mm), different cut advance rate (100, 200, 300, 350, 400 cm/min), different cutter disk rotation speed (1540, 1770, 2550 rpm). Results indicate that increasing in cut depth and cut advance rate, lead to increase in vibration intensity. Vibration intensity quantity even increased 6 times, when cut advance rate varies from 100 to 400 cm/min. Using SPSS software, after laboratory result investigation and statistically data analysis, vibration signal predicting statistical models are presented. Results of statistical tests indicates that the best fitting models enable predicting vibration quantity accurately and precisely with correlation coefficient range of 0.92 - 0.87, confidence level of 90% and error less than 10%.افزایش بیش از حد مجاز ارتعاش در فرآیند برش سنگ، علاوه بر افزایش پرت سنگ، باعث ایجاد کمانش، انحراف و در نهایت شکست ابزار میشود. بنابراین بررسی و پیشبینی میزان ارتعاش طی فرایند برش، امری لازم و ضروری میباشد. در این تحقیق سعی شد با انجام مطالعات آزمایشگاهی و آماری، به بررسی و پیشبینی ارتعاش طی فرایند برش پرداخته شود. بدین منظور یک دستگاه برش در مقیاس آزمایشگاهی به همراه تجهیزات اندازهگیری ارتعاش تهیه گردید. مطالعات تحت شرایط مختلف عملیاتی در عمق-های مختلف برش (15، 22، 30 و 35 میلیمتر)، نرخهای مختلف پیشروی (100، 200، 300، 350 و 400 سانتیمتر در دقیقه) و سرعت-های مختلف چرخش دیسک (2550، 1770 و 1540 دور در دقیقه) بر روی یک نمونه سنگ کربناته انجام شد. نتایج نشان داد که با افزایش مقدار عمق برش و نرخ پیشروی، میزان شدت ارتعاشات افزایش مییابد. به طوریکه نسبت این تغییرات در نرخهای پیشروی 400 به 100، بیش از 6 برابر بود. پس از بررسی نتایج آزمایشات و انجام مطالعات آماری، مدلهای آماری برای پیشبینی سیگنالهای ارتعاشی با کمک نرم افزار SPSS ارائه شدند. نتایج حاصل از آزمونهای آماری نشان داد که بهترین مدلهای برازشی قادر به پیشبینی میزان ارتعاشات طی فرایند برش با ضریب تبیین 92/0 و 87/ با سطح معنی داری بالای 90 درصد و خطای کمتر از 10 درصد میباشند.انجمن زمین شناسی مهندسی ایراننشریه انجمن زمین شناسی مهندسی ایران2228-524514320211122Investigation of Different Grinding Aids Effects on the Cement Quality and Grinding Efficiency; Case Study: Urmia Cement Plantبررسی تاثیر کمک خردایشهای مختلف بر روی کیفیت سیمان و راندمان خردایش سیمان تولیدی؛ مطالعۀ موردی کارخانه سیمان ارومیه3345133730FAحجت حسین زاده قره قشلاقگروه مهندسی معدن دانشگاه صنعتی ارومیهسجاد چهره قانیگروه مهندسی معدن دانشگاه ارومیهعارف علیپورگروه مهندسی معدن دانشگاه صنعتی ارومیهسینا سلطانعلی نژادگروه مهندسی معدن دانشگاه ارومیهJournal Article20200731In this study, the effects of four grinding aids with three different levels on the three important characteristics of the cement, namely the specific surface area, the compressive strength of the concrete and the grinding efficiency (energy saving), have been evaluated in the clinker grinding process. In the first step, by kinetic grinding tests, the required grinding time to reach to the Blaine value of Ordinary Portland Cement (OPC) of the Urmia Cement Plant (3636 cm2/g) was obtained, which was 78.24 minute by 2.19% deviation. Then, 13 laboratory grinding tests were performed by using of Urmia cement and four grinding aids (in 3 different doses of 0.02, 0.05 and 0.08%) and the results were compared. The results showed that the combination of Triisopropylamine 0.08% (TIPA-0.08) with a Blaine number of 4032 cm2/g and a grinding efficiency of 31.57% had the greatest effect on the fineness and grinding efficiency. On the other hand, the prepared samples of the all combinations were used to test the compressive strength of 2, 7 and 28 days. The results showed that the highest increase of compressive strength for all ages was obtained by TIPA-0.08 which was 36.92%, 31.23% and 21.85% for 2, 7 and 28 days, respectively.در این تحقیق اثر چهار نوع کمک خردایش (TIPA، TEA، HA و NC) در سه سطح مختلف بر روی ویژگیهای بسیار مهم سیمان یعنی مساحت سطحی ویژه (عدد بلین)، مقاومت فشاری بتن و راندمان خردایش (صرفهجویی انرژی) در فرآیند خردایش کلینکر کارخانه سیمان ارومیه مورد بررسی قرار گرفته است. در مرحلۀ اول، با انجام آزمایش خردایش سنتیکی، زمان آسیای مورد نیاز برای رسیدن به عدد بلین مورد نظر کارخانه (3636 سانتی مترمربع بر گرم) برابر 24/78 دقیقه بدست آمد. سپس، 13 تست خردایش در مقیاس آزمایشگاهی با استفاده از ترکیب سیمان کارخانۀ ارومیه و چهار نوع کمک خردایش در 3 سطح مختلف 02/0، 05/0 و 08/0 درصد انجام گرفت. نتایج نشان میدهند که ترکیب تری ایزوپروپانول با سطح 08/0 درصد (TIPA-0.08) با عدد بلین 4032 سانتی مترمربع بر گرم و راندمان خردایش 89/10 درصد دارای بیشترین تاثیر در ریزی و راندمان خردایش است. همچنین، برروی نمونههای بتن تهیه شده از تمامی ترکیبها آزمایش های مقاومت فشاری 2، 7 و 28 روزه انجام گرفت. نتایج نشان میدهند که بیشترین افزایش مقاومت برای تمامی سنین متعلق به ترکیب TIPA-0.08 بوده است که مقدار افزایش برای مقاومتهای فشاری 2، 7 و 28 روزه به ترتیب 92/36، 23/31 و 85/21 درصد نسبت به حالت مرجع (بدون کمک خردایش) شده است. از طرفی، نتایج حاصل از آزمایشهای خردایش و مقاومت فشاری بتن، نشان دهندۀ یک توافق نسبی بین راندمان خردایش – مقاومت فشاری بتن هستند.انجمن زمین شناسی مهندسی ایراننشریه انجمن زمین شناسی مهندسی ایران2228-524514320211122The effect of geopolymer on loess soil stabilization (Case study; Loess soil of Gorgan province)بررسی تاثیر ژئوپلیمر برتثبیت خاک لس (مطالعه موردی خاک لس استان گرگان)4764133731FAلیلا کرمیگروه عمران، دانشگاه قمعلی محمد رجبیزمین شناسی مهندسی دانشگاه تهرانJournal Article20190917Losses are among the collapsible soils that, if saturated, their volume will rapidly drop. Iran is one of the countries where Loess soils are spread in different parts of it. The purpose of this study is to improve the strength parameters of loess Gorgan (North of Iran) using different ratios of geopolymer (a combination of loess and metakaolin). For this purpose, in this study, in addition to conducting index tests, a series of uniaxial compressive strength, Brazilian tensile strength, compressive wave velocity and modified compaction tests have been done. Furthermore, SEM, EDX and XRD tests have been conducted to investigate micro-structural features of non-stabilized and stabilized soils. In the samples stabilized with geopolymer, with increasing ratio of loess to metakaolin and the curing time (with fix alkaline activator solution), uniaxial compressive strength, tensile strength and compressive wave speed decreases. So that, with increasing curing time, the uniaxial compressive strength of the specimens decreased to 0.83 and the rate of this decrease was greater in the first 7 days. The results of XRD analysis and SEM images show that the disperse structure of loess soil is altered by the addition of geopolymer and by the production of alumina-silicate gel which results in increasing strength, decreasing porosity and homogeneity of loess soil structure.لسها از جمله خاکهای فروریزشی هستند که در صورت اشباع شدن، کاهش حجم ناگهانی و زیادی از خود نشان میدهند. کشور ایران از جمله کشورهایی است که لس در بخش های مختلفی از آن پراکنده شده است. هدف از این پژوهش، بهبود پارامترهای مقاومتی خاک لس گرگان (شمال ایران) با استفاده از نسبتهای مختلفی از ژئوپلیمر (ترکیبی از لس و متاکائولن) می-باشد. بدین منظور، در این مطالعه علاوه بر انجام آزمایشهای شناسایی مجموعهای از آزمایشهای مقاومت فشاری تکمحوری، مقاومت کششی برزیلی، سرعت موج فشاری و تراکم اصلاح شده، همچنین آزمایشاتSEM ، EDX وXRD برای بررسی ریزساختار خاک تثبیت نشده و تثبیت شده انجام شده است. در نمونههای تثبیت شده با ژئوپلیمر، با افزایش زمان عملآوری و نسبت لس به متاکائولن با ثابت بودن میزان محلول فعال کننده قلیایی، مقاومت تکمحوری، مقاومت کششی و سرعت موج فشاری نمونهها کاهش مییابد. به طوری که با افزایش زمانعملآوری مقاومت فشاری تکمحوری نمونهها 83/0، کاهش یافته و نرخ این کاهش مقاومت در 7 روز اول بیشتر است. نتایج آنالیز XRD و تصاویر SEM نشان میدهند که ساختار پراکنده خاک لس در اثر افزودن ژئوپلیمر تغییر میکند و با تولید ژل آلومینوسیلیکاتی منجر به افزایش مقاومت نهایی، کاهش تخلخل و همگن تر شدن ساختار خاک لس میشود.انجمن زمین شناسی مهندسی ایراننشریه انجمن زمین شناسی مهندسی ایران2228-524514320211122Application of probabilistic neural network method for classification of Yazd, Ali-Abad copper deposit بکارگیری روش شبکه عصبی احتمالاتی بهمنظور طبقهبندی عیار کانسار مس علیآباد یزد6576133732FAرضا احمدیعضو هیئت علمی گروه مهندسی معدن، دانشکده مهندسی علوم زمین، دانشگاه صنعتی اراکمسعود لشگری آهنگرانیگروه مهندسی معدن، دانشگاه صنعتی اراک، اراک، ایرانJournal Article20200910In the present research, a probabilistic neural network based on the Bayesian probabilistic algorithm was employed to classify the grade of Ali-Abad copper deposit in Yazd. For this purpose, induced polarization (IP) and resistivity (Rs) geophysical data and rock type of exploration borehole cores as geological information corresponding to four geophysical profiles, DD-1, PD-2, PD-3 and PD-4 were used as input parameters as well as the copper grade of the boreholes as target parameter. To achieve the goal, 488, 528, 188, and 456 data were randomly collected from the sections related to DD-1, PD-2, PD-3 and PD-4 geophysical profiles so that 75% of total data were selected for training and 25% to test the probabilistic neural network. The performance of the proposed approach was evaluated by confusion matrix through the ratio of summation of data on the main diameter to the total test data, as well as determination of Commission and Omission errors. The results of the research show that the probabilistic neural network could estimate the test data for DD-1, PD-2, PD-3 and PD-4 profiles with accuracy of 60, 74, 60 and 83.3%, respectively which are reasonable considering the type of available data. In addition, the results were qualitatively evaluated through plotting isograde maps of four exploratory cross-sections over the geophysical profiles. This process was carried out using the assay data of exploration boreholes, gridding and the grid interpolation with the high accurate kriging estimation method, which was leaded to favorite results.در پژوهش حاضر شبکه عصبی احتمالاتی مبتنی بر الگوریتم احتمالاتی بایزین برای طبقهبندی عیار کانسار مس علیآباد یزد بکار گرفته شد. برای این منظور از دادههای ژئوفیزیکی قطبش القایی (IP) و مقاومت ویژه (Rs) و اطلاعات زمینشناسی نوع سنگ مغزههای حفاری گمانههای اکتشافی واقع بر روی چهار پروفیل ژئوفیزیکی بهنامهای DD-1، PD-2، PD-3 و PD-4 به-عنوان پارامترهای ورودی و پارامتر عیار مس گمانهها بهعنوان پارامتر هدف استفاده شد. برای دستیابی به مقصود بطور تصادفی تعداد 488، 528، 188 و 456 داده بهترتیب از مقاطع منطبق بر پروفیلهای ژئوفیزیکی DD-1، PD-2، PD-3 و PD-4 برداشت شد که 75 درصد از کل دادهها برای یادگیری و 25 درصد برای ارزیابی عملکرد شبکه عصبی احتمالاتی انتخاب شد. عملکرد رویکرد پیشنهادی از طریق نسبت مجموع دادههای روی قطر اصلی به کل دادههای آزمون توسط ماتریس درهمآمیختگی و تعیین خطای کامیژن و آمیژن، مورد ارزیابی قرار گرفت. نتایج پژوهش نشان میدهند که شبکه عصبی احتمالاتی توانسته داده-های آزمون مربوط به پروفیلهای DD-1، PD-2، PD-3 و PD-4 را بهترتیب با 60، 74، 60 و 3/83 درصد دقت برآورد نماید که با توجه به نوع دادههای دردسترس، قابل قبول میباشند. همچنین نتایج از طریق ترسیم نقشه همعیار چهار مقطع اکتشافی منطبق بر پروفیلهای ژئوفیزیکی، بهکمک دادههای عیارسنجی گمانههای اکتشافی، شبکهبندی و درونیابی شبکه با استفاده از روش تخمین دقیق کریجینگ، بطور کیفی مورد ارزیابی قرار گرفت که نتایج مطلوبی حاصل شد.انجمن زمین شناسی مهندسی ایراننشریه انجمن زمین شناسی مهندسی ایران2228-524514320211122A criterion to estimate the minimum and maximum underbalanced pressures of drilling mud in Iranian carbonate reservoirsارائه معیاری برای تخمین حداقل و حداکثر فشار فروتعادلی گل حفاری در مخازن کربناته ایران7788133733FAناصر بهنامدانشگاه بین المللی امام خمینی (ره)مهدی حسینیدانشگاه بین المللی امام خمینی (ره)محمد احمدیدانشگاه صنعتی شاهرودJournal Article20200617Underbalanced drilling is in fact the best drilling method for oil reservoirs that their pressure has been reduced. This study aimed at obtaining a criterion for estimating the minimum and maximum underbalanced presUnderbalanced drilling is an advanced technology and a drilling operation in which the drilling fluid pressure inside the well is less than the pore pressure of sures of the drilling mud for enhancing oil recovery and preventing damages to the formations in the Iranian carbonate reservoirs. To this end, data on 13 wells in various Iranian oil fields were first collected. The oil wells were simulated at different drilling mud pressures with the help of the finite difference method (FDM)-FLAC2D. The elastoplastic normalized yielded zone area (NYZA) method was used for stability analysis and estimation of the minimum and maximum underbalanced pressures of the drilling mud. The NYZA diagram was plotted separately for each well. Considering the drilling mud pressures on the NYZA diagram in the range of NYZA=1 to the pore pressure, a minimum and maximum drilling mud pressure of NYZA=1 and NYZA=0.2 was calculated, respectively. Eventually, a correlation was proposed as a fraction of the pore pressure to estimate the minimum and maximum underbalanced pressures. This correlation is expressed as a factor or fraction of the pore pressure. The minimum and maximum underbalanced pressures of the drilling mud to enhance oil recovery and prevent damage to the formation can be estimated solely by inserting the pore pressure of the formation in this correlation.حفاری با فشار زیر تعادل در واقع بهترین روش برای حفاری مخازن نفتی میباشد که فشار آن ها به دلیل تولید روزمره کاهش یافته است. این تحقیق با هدف بدست آوردن معیاری برای تخمین حداقل و حداکثر فشار فروتعادلی گل حفاری به منظور ازدیاد برداشت نفت و جلوگیری از آسیب به سازند در مخازن کربناته ایران انجام شده است. برای رسیدن به این هدف ابتدا یک سری اطلاعات، شامل 13 چاه از میدان های مختلف نفتی ایران جمع آوری شده و سپس با استفاده از نرم افزار FLAC2D که یک برنامه عددی بر مبنای روش تفاضل محدود است، به مدلسازی چاه نفت در فشارهای مختلف گل حفاری پرداخته شده و در نهایت برای تحلیل پایداری و تخمین حداقل و حداکثر فشار فروتعادلی گل حفاری، به روش الاستوپلاستیک از روش تعیین سطح نرمالیزه (NYZA) استفاده شده است که پس از رسم نمودار NYZA برای هر چاه به صورت جداگانه، با در نظر گرفتن فشارهای گل حفاری روی نمودار NYZA در بازه بین 1=NYZA تا فشار منفذی، حداقل و حداکثر فشار گل حفاری به ترتیب در 1=NYZA و 0/2=NYZA محاسبه شده و در نهایت رابطه ای به صورت نسبتی از فشار منفذی برای تخمین حداقل و حداکثر فشار فروتعادلی گل حفاری بدست آورده و ارائه شده است. این رابطه به صورت ضریب یا نسبتی از فشار منفذی بیان شده که در آن، تنها با داشتن فشار منفذی سازند می توان حداقل و حداکثر فشار فروتعادلی گل حفاری را به منظور ازدیاد برداشت نفت و جلوگیری از آسیب به سازند تخمین زد.انجمن زمین شناسی مهندسی ایراننشریه انجمن زمین شناسی مهندسی ایران2228-524514320211122Investigating and comparing the resistance characteristics of sandy soils with changing the percentage of moisture and fine-grained characteristicsبررسی و مقایسه ویژگیهای مقاومتی خاکهای ماسهای با تغییر درصد رطوبت و مشخصات بخش ریزدانه89103133734FAمهدی خداپرستگروه مهندسی عمران- دانشکده فنی و مهندسی-دانشگاه قم- قم- ایران0000-0002-4007-4093مرضیه یوسفعلیگروه مهندسی عمران- دانشکده فنی و مهندسی-دانشگاه قم- قم- ایرانفاطمه وحیدی نیاگروه مهندسی عمران- دانشکده فنی و مهندسی-دانشگاه قم- قم- ایرانJournal Article20200622In nature, sandy soils are rarely clean and often contain some clay and silt. These fines grain have a significant effect on the resistance and dilation behavior of sandy soils. Therefore, in this study, resistance and dilation behavior of sand mixture with fine grains such as silt and clay using a small scale direct shear test have been studied. Tests are conducted on specimens of sand with various fine content ranging from 0 to 40%, density of 30, 60 and 90 percent and the samples are subjected to three normal stresses 0.5, 1.0 and 1.5 kg/cm2 with two percent of optimum and saturation moisture. The test results show with increase in percentage of fine grains, the shear strength of sandy soil decrease and with increase in percentage of clay the shear strength decreases further. Also, dilation angle and angle of friction decreases with increase fine grains content and cohesion parameter increases with increase fine grains, Of course, it more increases with increase clay content and the rate of change of the cohesion parameter increases with increasing fine-grained percentage.در طبیعت، خاک ماسهای به ندرت به شکل تمیز و خالص میباشد و اغلب دارای مقادیر مختلفی ریزدانه است. انتظار میرود که حضور ریزدانه در خاک ماسهای عملکرد مقاومت برشی و اتساعی خاک ماسه را تحت تأثیر قرار دهد؛ لذا در تحقیق حاضر با یک ایده جدید در ساخت نمونه ها، رفتار مقاومتی و اتساعی مخلوط ماسه ترکیب شده با ریزدانه با استفاده از دستگاه برش مستقیم کوچک مقیاس با دو نوع ریزدانه سیلت و رس و در چهار درصد ریزدانه متفاوت 10، 20، 30 و 40 و در سه تراکم نسبی 30، 60 و 90 درصد و با دو درصد رطوبت بهینه و اشباع، آماده و تحت تنشهای قائم 0.5، 1 و 1.5 کیلوگرم بر سانتیمتر مربع مورد بررسی قرار گرفتند. نتایج این تحقیق نشان میدهد که افزایش مقدار ریزدانه منجر به کاهش مقاومت برشی خاک ماسهای میگردد و ریزدانه رسی مقاومت برشی خاک ماسه را بیشتر کاهش میدهد. همچنین افزایش درصد ریزدانه چه از نوع سیلت و چه از نوع رس سبب کاهش اتساع و زاویه اتساع و همچنین زاویه اصطکاک داخلی خاک ماسهای میگردد؛ البته رس نسبت به سیلت پارامترهای مذکور را بیشتر کاهش داده است. پارامتر چسبندگی نیز با افزایش ریزدانه افزایش مییابد و البته در مخلوط رسی پارامتر چسبندگی با افزایش رس، بیشتر افزایش یافته است. همچنین نرخ تغییرات پارامتر چسبندگی با افزایش درصد ریزدانه افزایش مییابد.انجمن زمین شناسی مهندسی ایراننشریه انجمن زمین شناسی مهندسی ایران2228-524514320211122Investigation of Reactivation of Fault and Wellbore Stability Analysis by the Depletion of Hydrocarbon Reservoirsبررسی امکان فعالیت مجدد گسلها و تحلیل پایداری چاه براثر تخلیه مخازن هیدروکربنی133728FAمرتضی حسن زادهگروه مهندسی نفت، دانشگاه آزاد اسلامی، واحد امیدیه، امیدیه، ایرانمحمد آبدیدهDepartment of Petroleum Engineering, Omidiyeh Branch,Islamic Azad University,Omidiyeh, IranJournal Article20200318Over time and production from the reservoir, the pore pressure of the production layer decreases if there is no source of pressure supply. This reduction in pressure directly alters the amount and direction of stresses. Changes in the amount of stresses can cause geomechanical changes in the reservoir and production layers. If the reservoir layers are faulted, reducing the reservoir pressure can activate these faults and also change the tensile strength of the well bore for new drilling in the discharged layer. This research was conducted in one of the reservoirs of southwestern Iran. In this reservoir, three production layers with different thicknesses were examined and the probability of reactivation of faults and tensile strength in the initial state and after the pressure drop of 1800 psi was evaluated. In layer 1, the value of the stress path was 0.67, which due to the fact that it is tangent to the critical stress value, the faults will be reactivated by producing from the reservoir and reducing the reservoir pressure in this layer. Also in this layer, the maximum weight of the drilling mud allowed for non-failure of rock traction in the initial state is 17.81- 25.13 PPG and after a reduction of 1800 psi of layer pressure, it is in the range of 15.07- 23.42 PPG. . In addition, the most resistant state of the well bore is drilling with an angle of 60 degrees and in the direction of minimum horizontal stress.با گذشت زمان و تولید از مخزن، فشار منفذی لایه تولیدی در صورت نبود منبع تامین فشار کاهش مییابد. این کاهش فشار بطور مستقیم باعث تغییر در مقدار و جهت تنش های برجا میشود. تغییر در مقدار تنش های برجا می تواند باعث تغییرات ژئومکانیکی در مخزن و لایه های تولیدی گردد. درصورتیکه لایه های مخزن گسل خورده باشد، کاهش فشار مخزن می تواند منجر به فعال شدن این گسل ها و همچنین تغییر مقاومت کششی دیواره چاه جهت حفاری جدید در لایه تخلیه شده گردد. این تحقیق در یکی از مخازن جنوب غرب ایران انجام شده است. در این مخزن سه لایه تولیدی با ضخامت های متفاوت مورد بررسی قرار گرفتند و احتمال فعالیت مجدد گسلها و مقاومت کششی در حالت اولیه و پس از افت فشار 1800 پوند بر اینچ مربع مورد ارزیابی قرار گرفت. در لایه شماره 1 مقدار مسیر تنش 67/0 بدست آمد که با توجه به اینکه مماس بر مقدار تنش بحرانی می باشد، با تولید از مخزن و کاهش فشار مخزن در این لایه گسلها مجددا فعال خواهند شد. همچنین در این لایه حداکثر وزن گل مجاز برای عدم شکست کششی سنگ در حالت اولیه 81/17 -13/25 پوند بر گالن و پس از کاهش 1800 پوند بر اینچ مربع فشار لایه، در محدوده ی 07/15-42/23 پوند بر گالن قرار دارد. همچنین مقاوم ترین حالت دیواره چاه، حفاری با زاویه 60 درجه و در جهت تنش افقی حداقل می باشد.